The gaming chair can be reclined by pulling the lever to the end and putting your weight on it, as shown in the image.

The gaming chair can be reclined by pulling the lever to the end and putting your weight on it, as shown in the image.

When reclining for the first time after purchase, the lever may be stiff and it may be difficult to pull the lever all the way. In that case, move the lever repeatedly.

New gas cylinders shortly after purchase may have some hardening of the oil inside and may be difficult to move.

With the load applied to the seat while sitting on the chair, pull up the control lever firmly and try to adjust the height. (If it is difficult to move, move the lever repeatedly).
* Once it moves, it will move smoothly after that.

For more information, please refer to the FAQ (Frequently Asked Questions), “How do I raise and lower the gas cylinder?

■ How to care for your office chair

  • When wiping off dirt on the surface:

    • When wiping off dirt on synthetic leather parts such as PVC leather, PU leather, polyester mesh and nylon mesh parts, soak a towel, etc. in diluted neutral detergent and lightly wipe off.
    • Make sure to wipe thoroughly with a dry cloth after wiping. If moisture remains, the synthetic leather may deteriorate. For the leather part, please use a commercially available leather cleaner.
  • ■ Allowing/preventing rocking

    • Allowing/preventing rocking

      Pull the control lever on the metal part of the seat support outward to release the rocking.

    • Allowing/preventing rocking

      Push the control lever on the metal part of the seat support inward to prevent rocking.

    • Allowing/preventing rocking
  • ■ Adjusting the rocking

    Adjusting the rocking

    The firmness of the rocking can be adjusted slightly with the spring-loaded screw on the back of the seat.

    Since this screw is spring-loaded, it may be stiff and difficult to turn. Please refer to the figure below to turn the screw.

    • * The adjustable range is small, so it may be difficult to feel the change in rocking firmness.
    • * If the rocking is soft, the chair will gain momentum when you sit on it, which may cause you to fall.
    • * When the rocking adjustment screw is tightened, the plastic lid at the tip will come off, revealing the screw part inside, but there is no problem in use. Please keep the lid as needed.
    Adjusting the rocking
  • ■ If you need to disassemble the chair for moving or other reasons…

    • * Gas cylinders are difficult to remove once assembled, but may be removed by using a rubber hammer.
    • * Do this at your own risk. We are not liable for injury or damage caused by the work.
    • * Please wear non-slip gloves when working to avoid injury.
    • * It may or may not come off easily depending on the usage. If the chair is not used much, it may come off relatively easily.
    • 1. First, remove the metal part of the seat support from the seat surface. (Remove the screws.)

    • 2. Remove the legs from the removed seat support metal part.

      Use a commercially available rubber hammer or similar tool to avoid scratching the parts.

      Tap the red circle part of each leg repeatedly and remove it with the vibration.

      • * There is no need to hit it hard, just be careful not to damage the parts.
      • * Please be careful not to injure yourself as the detached legs may fall.
      • If you need to disassemble the chair for moving or other reasons...
      • If you need to disassemble the chair for moving or other reasons...
    • 3. After the legs are removed, remove the gas cylinder from the seat support metal part in the same way.

      Tap the red circle part on the metal part of the seat support lightly and repeatedly to remove it by vibration.

      • * There is no need to hit it hard, just be careful not to damage the parts.
      • * Please be careful not to injure yourself when the metal part of the seat supporter falls.
  • ■ Product Disposal

    When disposing of the product, be sure to dispose according to the disposal classification of each local government.

    Never disassemble the gas cylinder. It is very dangerous.

  • ■How to raise and lower the gas cylinder?

    • Q. How do I raise and lower the gas cylinder?
    • Q. How do I raise and lower the gas cylinder?

    Lift the control lever to raise or lower the seat.

    The new gas cylinder may be difficult to move at first because some of the oil inside may harden. While sitting in the chair, pull up the control lever firmly (if it is difficult to move, move the lever repeatedly). Once it moves, it starts moving smoothly.

    As shown in the figure above, when the operation lever is lifted, the switch at the tip of the gas cylinder is pushed in.

    When you lift the control lever, you will feel as if you are pushing in the button. When you lift your hips with this button pushed in, the seat moves up, and when you pull the lever while sitting and putting your weight on it, the seat moves down.

    If you weigh less than 50kg, it may be difficult to lower the seat once it is raised. If this is the case, please ask someone to push you to adjust the height.

  • ■ About the gas cylinders used in our product

    All of the gas cylinders used in our products contain 100% nitrogen gas.

    Use the gas cylinders in a normal way. Failure to do so may cause explosion.

    Although this product has sufficient durability, please follow the precautions listed below when handling.

    • ・Do not subject the gas cylinder to shocks that could damage it or cause it to break.
    • ・Do not apply heat, fire or pressure.
    • ・Observe the precautions described in the product’s instruction manual.